Making of the Eiffel Tower using matches

Yes, this is a project that I started with a long time ago and I didn't finish yet but I want to share with you. Since it will take a long time to finish, I will share with you enough to show the way to the friends who want to start.
Our project is to build a model of the Eiffel Tower. Using very simple materials you can make a very wonderful model with some time and skill. It was something you always wanted to see and do on the internet, so I started at the end :)
Let me first say the necessary materials;

Match
Glue
utility knife
ruler, pencil
Hot silicone (for fixing the model to the floor and for bonding some pieces together)
model
+ time and patience :)
Now we start with the first pole of our tower is the only thing you need to pay attention to the floor of the room poles can be any angle, I drew a model on the ground I'm going to draw a kind of guide towers will install on this guide lines. as in the photo below.

After closing this shape, we peel the ends of the matches with the help of the utility knife. then we start to stick the matches with the help of glue. in the picture below I will give you a photo of how I do it, but like I said, this is my way of doing what you want to do in a different way. That was the most practical way for me :)

As shown in the picture, we do 4 match lengths. We glued the matches together like the one in the 1st section. the top and the last remaining half of the final part of the remaining part of the paste to fit exactly the other part will fit exactly the other side. In the second part, in the first part, I show a red arrow with a number of more matches. at the end of the second part (side view) as you see a figure comes out. The green side of the match will be where we will stick our other matches.

yes, we'll have a picture of you. The two pieces are glued with the glue.

Note: Guideline 16 cm in the picture shown in the 16 cm. room about 16 cm :)

then we make 4 pieces of these pieces.

I use the syringe for the needle, I use the glue to drive with it is not something else: D with a thin object you can drive the glue. . . Oh, by the way, you can say there are 3 of them.
then we came to process the inside of the 4 pieces that we have made the cross-patterned ktımlara.

friends in the meantime, I forgot to say that the above 4 pieces of the 2 pieces of the guide to the side of the picture in the opposite direction of the other two will be done in the direction of the right side. why is that? because they combine these four parts with one pole, while the other two parts must look on the outside. below show me soon :)

In the meantime, I'll tell you that in each part of the 4 compartments formed only cross section of the cross pattern of the top 3 will be another girl.

as in the picture below. . .

Note the fully laid out (only 3-compartment) matches before processing the portion that is diagonal in the shapes. Section 4, ie the upper part, does not work as in the figure above. (this is my way of working you can do more detailed depending on you)

In the picture above, you can see the part that will be done in the right angle and the left part in the right angle.

And we do 4 pieces of silicon with the help of the ground on the ground one by one we are pasting each other to hold each other to hold each other silicon.

yes the first pole is seen above.

then we do the 2nd and the fourth poles with the same method, we do, but how much intervals do you place them? This is one of the most difficult parts of the job. . . I'il try to tell you how I did it.

yes, as you can see, between the ends of the two towers will be approximately 15cm (can be +1, -1). . .

After the 3rd and 4th lines, there was a picture that I drew in the first place and they made bars like this (these children make them longer and shorter by measuring them, too much longer, cut them as they stick the poles to the poles). wishing silicone can use. . . then we fill them with small matches that we cut vertically between them.